C1163 Engine Trouble Code

When you check engine light came on code C1163 the reason should be ABS Warning Light ON. However your vehicle's manufacturer may have a different definition for the C1163 OBD-II Diagnostic Chassis (C) Trouble Code. So you should chech it on our car models.

When the DTC check engine light comes C1163 code on the first you can check is the gas related maybe gas cap. Pull over, retighten it, and take a look at the cap to see if it has any cracks inside. Go on driving and to see if the check engine light turns off automaticly. On the other hand, you can buy a gas cap for about $4.5 at an auto parts store. All you need to do is take the old one take off and take on the new one. If you've already bought it to the store, you might as well just replace the cap. While not car-threatening, it's good to take care of this right away to improve gas mileage/km.

C1163 Code Meaning :

The oxygen (02) sensors on your car measure the oxygen in the exhaust to determine how rich or lean the ratio of fuel and air are in the cylinders. Optimizing this mixture means better fuel economy and fewer exhaust emissions.

C1163 OBD-II Diagnostic Chassis (C) Trouble Code Description

C1163 OBD-II Trouble Code The steering angle sensor detects the rotation amount, angular velocity and direction of the steering wheel, and transmits the data to the ABS actuator and electric unit (control unit) via Control Are C1163 code. Engine Oil Temperature Sensor Malfunction and Injection Pump Fuel Metering Control 'A' High (Cam/Rotor/Injector) causes most of code C1163.

Reason For C1163 Code

C1163 the main thing to check is to verify the operation of the VCT solenoid in the engine. You're looking for a sticking or stuck VCt solenoid valve caused by contamination. Refer to vehicle specific service repair manual to perform component tests for the VCT unit.

How To Repair C1163 Code

Before starting let's see C1163 repairing process steps:

• Qualified technicians will begin by using a scan tool to access C1163 code stored in the ECU.
• Technicians will note C1163 code present and any freeze frame data associated with them.
• After all, if you sure the engine trouble is finished, the code will be cleared.

As you idle at a light or before positioning your vehicle in gear and you see that your engine is starting to create strange sounds, switch your oil filter and also inspect the pressure regulator to attempt and adjust the error. If you struggle to start your vehicle and notice it fails to turn over right away, it can also indicate a defective fuel pressure regulator.

C1163 code is causing changes to the performance of the vehicle, this code will illuminate the Check Engine light, making it impossible to pass an OBD-II emissions test. Getting this problem addressed may also help you avoid expensive repairs to the clutch, primary pressure solenoid, and other parts of the transmission system later on.

Diagnosis Of Engine Error OBD Code C1163

It's essential to diagnose this trouble code. Then are some way which a handyperson should follow for diagnosing the problem that started a C1163 trouble code to be stored

The first step is introductory and is about reacquiring all the canons that have been set. For this, the individual scanner will have to be plugged into the individual harborage of your vehicle. Make sure you indurate frame the data. Any canons that were set previous to the C1163 code will have to be sorted first, as they may have been the reason for the law to set in the first place. It's always good to rule that out.

The coming step is to run a introductory examination of all the electrical circuits, connectors, wiring etc for damages similar as becks, erosion, fraudulent legs etc. All of these will have to be repaired or replaced. After that's sorted, clear the canons and go on a test drive to see if it resets. In case it resets, you'll have to continue your opinion. Depending on your vehicle you may have a vacuum operated selector or a vacuum solenoid if it's electrically actuated. In the case of the former, a hand held vacuum pump will have to be used to testit.The purpose is to see if the internal stopcock is getting turned by the selector, motor or solenoid. In order to do this, a command can be transferred to the system with scanner or by driving the vehicle under the special conditions that will spark the system. While this is passing keep an eye on the checkup tool data for the result.